How To Repair Shutter Slats

Plantation shutters have been a popular window treatment for many years. They offer lots of great benefits like sun command and actress insulation, which really comes in handy when the weather turns super common cold like information technology has been lately.

If you've always shopped for plantation shutters, you lot probably know that they are usually fabricated of either wood or a man-made product like vinyl or plastic, sometimes referred to every bit "polywood." I'1000 a big fan of wood shutters considering they are ordinarily lighter weight than vinyl or made-made products, which ways less issues with panels sagging, especially in larger windows.

Another big advantage wood shutters have over vinyl/plastic shutters is that normally man-made panels do not take a way to adjust or tighten the louvers (tension adjustment screws) if they become loose or brainstorm to sag downward over time. Information technology's pretty inevitable that louvers will somewhen start to loosen up over time due to everyday use.

There are a few shutters out in that location that have springs built into the panels. I've e'er shied away from those because if the jump goes bad, there's usually cypher you can practice but replace the whole panel.

Some less-expensive wood shutters don't have tension aligning screws either, so when shopping for shutters it's of import to inquire almost this feature. If you have forest shutters and you've noticed a louver sagging or hanging down, check to see if it has a tension aligning spiral. If it does, you can set the loose louver in seconds. Let me show y'all how information technology works.

Each winter I volition find a section of louvers on a few of the shutter panels I open and shut on a regular footing, begin to hang down. The reason this tends to happen this time of year is because wood shrinks in the winter. If I did nothing, chances are the tension would improve or mayhap fully recover once warm conditions/humidity returns in the jump and the wood expands back out over again. Simply it doesn't ever and who wants to wait at floppy louvers all winter. Right?

If you lot have a louver panel sagging or hanging downward in one of your windows and it won't stay in an open position as it should, open the console and look for a trivial holes(south) down the inside border of the panel. That'southward where you lot'll unremarkably discover the tension adjustment screws if your panels have them congenital-in. There'southward normally one tension adjustment screw for each section of the panel. You lot'll notice below, my shutters have one screw for the summit department and one screw for the lower section on each console.

Hither'southward a little closer view of the hole where the tension aligning screw is subconscious.

Tightening your loose louvers back up is super easy if you accept plantation shutters with tension adjustment screws built-in. Merely take a Philips head screwdriver, insert it into the hole, and while belongings the bodily louvers steady with your left paw, give the spiral a tiny footling nudge clockwise with your correct hand. If you don't hold the louvers still with i hand while tightening the screw, the louvers will turn and y'all can't arrange the tension.

Important: The reason I say to give the screw just a niggling "nudge" is considering usually the screw just needs the tiniest turn to tighten the louvers. Don't turn the screw very much or you could risk over-tightening. Unremarkably a teeny, slight plough of the screw will exercise the job. Of course, you'll desire to bandy those directions if you lot're left-handed and prefer using a screwdriver with your left manus.

All fixed!

If yous take a window in your home with bi-fold plantation shutter panels, the screws are usually located in between the shutter panels. Another window where I normally encounter a loose louver or 2 during the wintertime is here in my breakfast room. (meet arrows below pointing to loose louvers) During the winter months when it's cold out and the leaves are off the copse, I open and shut the louvers in here almost daily, and so i or 2 will tend to loosen up when information technology's super common cold out.

Again, the tightening process only takes seconds for bi-fold shutters, too. Simply open dorsum your bi-fold panels and you should see holes where the tension adjustment screws are hidden in betwixt the panels. Some manufacturers may put the tension adjustment screw on the outside edge of the panel, but well-nigh hide information technology inside the panel where it isn't visible.

Hope this is helpful for anyone running into this issue from time to time. If yous have any questions well-nigh plantation shutters or about tightening up the tension on the louvers, permit me know and I'll be happy to respond them in the comments below.

If plantation shutters is something you take an interest in, I've written a more than all-encompassing post answering a lot of questions most them here: Plantation Shutters, Versatile Window Treatment

Related posts:

*If a mail is sponsored or a product was provided at no charge, information technology will be stated in mail. Some links may exist affiliate links and as an Amazon Associate, I may earn from qualifying purchases. *

Source: https://betweennapsontheporch.net/how-to-fix-loose-sagging-louvers-on-plantation-shutters/

Share this post